GreatWhite120™ Large Area Repair Concrete

MSDS (PDF)  MSDS for Activator (PDF)  Material Data Sheet (PDF)  Data Charts  Request Quote  Request Product Information Documents marked as PDF require Adobe Acrobat Reader to view

GreatWhite120™ is an extremely versatile, cementitious, rapid setting, semi-leveling structural repair concrete. It is a single component powder that is water activated. GreatWhite120™ has 20 minutes of working time and will reach compressive strengths of more than 2,500 psi within 2 hours from the addition of water. GreatWhite120™ can be applied in ambient temperature ranges from 30 to 120 degrees Fahrenheit. GreatWhite120™ finishes like traditional Portland based concrete and cleans up easily with water. GreatWhite120™ rapid, large area concrete has been designed for use with volumetric concrete mixers for large scale repair projects.

Recommended Uses
GreatWhite120™ has been designed for horizontal, sloped and vertical applications providing for rapid return to service of 2 hours for roads and bridge decks, aviation runways, parking garages, piers, columns, foundations, parking lots, marine access ramps and any other repair or new construction application application where rapid early strength gains are required.
 
Features and Benefits

• Application surface temperatures above 120°F/49°C or below 30°F/-1°C.
• Not for submerged applications.
• Will not bond to polymers

Unit Weight (with water, sand & aggregate)
146lb/ft³ (2338 kg/m³) with 6% Air Entrainment
156lb/ft³ (2498 kg/m³) without Air Entrainment

Setting Time
Set Times at 72°F/22°C at 2” (5 cm) material depth
Initial set: 20 - 30 minutes
Final set: 30 - 40 minutes

Volume Yield
Concrete (binder + sand + coarse agg. + H₂0 ) =
3.3yds³ (2.52m³) per 2,200 lb. Super Sack)
2.5ft³ (0.07m³) per 70 lb. bag)

Packaging
70 lb. Plastic Bag
2,200 lb. Super Sack

Shelf Life
1 year

Storage
Bags must be kept dry

Technical Data
Results provided by licensed engineering test laboratory and represent typical results from production materials. Actual results may vary from third party testing results; however, CERATECH’s materials meet and/or exceed established internal quality control standards, (available upon request) . All samples were air cured.

Site Preparation
Surfaces should be prepared in accordance with ICRI 03730, “Guide for Surface Preparation for the Repair of Deteriorated Concrete Resulting from Reinforcing Steel Corrosion.” and / or ACI 546R-96 “ Concrete Repair Guide” Concrete surface should be prepared by appropriate mechanical methods to obtain an exposed aggregate surface with a minimum surface profile of +/- 1/16” (1.5 mm) in accordance with ICRI 03732. Pre-existing coatings or surface treatments should be completely removed. Dry, clean, stable surfaces are required. Remove all standing water. Reinforcing steel should have no loose scale.

• 1.9 lbs of fine aggregate (sand SSD, Specific Gravity = 2.64)
• 2.5 lbs of coarse aggregate (ASTM No. 57 stone SSD, Specific Gravity = 2.68)
  OR 2.24 lbs of coarse aggregate (ASTM No. 7, 0.50” stone SSD, Specific Gravity = 2.68)
• Water - Project dependant (contact CERATECH TECHNICAL SUPPORT 1-888-341-2600)

• 133 lbs of fine aggregate (sand SSD, Specific Gravity = 2.64)
• 175 lbs of coarse aggregate (ASTM No. 57 stone SSD, Specific Gravity = 2.68)
  OR 157 lbs of coarse aggregate (ASTM No. 7, 0.50” stone SSD, Specific Gravity = 2.68)
• Water - Project dependant (contact CERATECH TECHNICAL SUPPORT 1-888-341-2600)

• 4180 lbs of fine aggregate (sand SSD, Specific Gravity = 2.64)
• 5500 lbs of coarse aggregate (ASTM No. 57 stone SSD, Specific Gravity = 2.68)
  OR 4928 lbs of coarse aggregate (ASTM No. 7, 0.50” stone SSD, Specific Gravity = 2.68)
• Water - Project dependant (contact CERATECH TECHNICAL SUPPORT 1-888-341-2600)

  
  GreatWhite120™ concrete binder has been optimized for use with Volumetric / Proportional mixing equipment. Blend the above components per traditional Portland based concrete procedures.

  Contact CERATECH Technical Support for additional information on mixing and placing GreatWhite120™

Application and Finish

• Surfaces of host concrete must be damp with no standing water.
• Working times based on ambient temperature, types of aggregate and total amount of water. Working times are also influenced by surface temperature, humidity and repair profile.
• Minimum profile thickness is 1.50” (3.8 cm) when using 0.50” (1.3 cm) aggregate or 3.00”(7.6 cm) when using 1.00” (2.5 cm) aggregate. There are no restrictions to the depth of the repair profile.
• Upon initial set, a broom finish can be applied. Upon final set, the material can be saw-cut, drilled, sanded and/or polished.
• Do not re-temper. The addition of water to the surface of the repair will negatively affect the materials final properties.
• General loading in 2 hours for wheeled traffic and 1 hours for foot traffic after addition of water. In ambient and/or surface temperatures below 32°F/0°C, extend the loading time by 60 minutes for each 10° below 32°F/0°C.
• All previously existing joints must be re-established within 1-2 hours of final set.
• Self-curing, (Protect with blankets or equivalent in ambient temperatures below 32°F / 0°F).
• Clean all tools and equipment with water prior to the material reaching final set.

• See Material Safety Data Sheet (MSDS).
• This document does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this document to establish appropriate safety and health practices and to determine the applicability of regulatory limitations prior to use.
• Dispose of water materials in accordance with Federal, State, and Local regulations.
• The use of a dust mask, safety goggles and gloves is recommended.
• Keep out of reach of children.

WARRANTY
CERATECH, Inc. (“CERATECH”) warrants that its products are free from defects in materials and workmanship. If any CERATECH product fails to conform to this warranty, CERATECH will replace the product at no cost to the buyer or refund the purchase price, at CERATECH’s election. Any warranty claim must be made within one (1) year from the date of the shipment of the product to the buyer. In no event shall CERATECH be liable to the buyer for any consequential or incidental damages of any nature. CERATECH MAKES NO OTHER WARRANTIES, EXPRESS OR IMPLIED, WRITTEN OR ORAL AS TO THE MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE OF ITS PRODUCTS AND EXCLUDES THE SAME. THERE ARE NO WARRANTIES WHICH EXTEND BEYOND THE DESCRIPTION ON THE FACE HEREOF.